GS610 Source Measure Unit
Brand: Yokogawa Electric Corporation
Images are representations only.
GS610 Source Measure Unit
Brand: Yokogawa Electric CorporationThe GS610 is a highly accurate and highly functional programmable voltage/current source that incorporates voltage/current generation and measurement functions. The maximum output voltage and current are 110 V and 3.2 A, respectively.
Evaluation of over a wide range of basic electrical characteristics is possible, because the GS610 can operate as a current source or a current sink.
Features- Source and sink operation up to 110 V/3.2 A (four-quadrant operation)
- Basic accuracy: ±0.02% (DC voltage generation)
- Sweep output at up to 100-µ intervals
- Comes with abundant sweep patterns (linear, logarithmic, and arbitrary)
- Stores up to 65535 points of source measure data in the internal memory
- Remote control and FTP using Web server function (Optional)
- Easy file operation with the USB storage function
Specifications
Accuracy
- ± 0.02 % of Setting - DC Voltage Generation
- ± 0.03 % of Setting - DC Current Generation
Approvals & Certifications
- AS
- BS
- CSA
- GB
- IEEE 488
- UL
- VDE
Communication
- Baud Rate: 9,600, 14,400, 19,200, 38,400, 57,600, or 115,200 bit/sec
- Ethernet Conforms to IEEE 802.3
- Full Duplex Transmission Mode - RS-232 Interface
- GPIB Interface Conforms to IEEE Standard 488
- RS-232 Serial Interface Conforms to EIA
- USB Conforms to Rev. 1.1
Consumption
- 200 VA Approximately
Current
- 20 μA to 3.2 A - Current Generation/Measurement Range
Delay Time
- 1 microsecond to 3,600 seconds - Source & Measurement Delay
Display
- 256 x 64 Dots Vacuum Fluorescent Display
- LED Display
- Organic Electroluminescent (EL) Display
Electrical Connectors
- BNC Connector - Synchronization Signal Input/Output Section
- D-Sub 15-Pin - External Input/Output Section
- D-Sub 9-Pin - RS-232 Interface
- RJ45 Connector - Ethernet Interface
- Typical B Connector (Receptacle) - USB Interface
Frequency
- 50/60 Hz
Humidity
- 20 to 80 % RH
Input
- TTL - I/O Level
Maximum Voltage
- ± 250 V Peak between the Generation (Measurement) Terminal & Case - Common-Mode Volatge
- 1 V between Output & Sense Terminal - Input/Output
- 110 V between High & Low Terminal - Input/Output
Measuring Time
- 1 microsecond to 3,600 seconds - Source-Only Operation
- 1 ms to 3,600 seconds - Source & Measure Operation
Mounting
- Rack-Mounted
Operating Temperature
- 5° to 40° C (41° to 104° F)
Output
- ± 0.5 A (Output Voltage of ± 110 V or Less) - Max.
- ± 1 A (Output Voltage of ± 60 V or Less) - Max.
- ± 2 A (Output Voltage of ± 30 V or Less) - Max.
- ± 3.2 A (Output Voltage of ± 12 V or Less) - Max.
- Current Sinking & Source is Possible Up to 110 V, 3.2 A & 60 W
Output Noise
- 8 mV Peak-to-Peak (DC to 20 MHz) with Generation at 2 V Range & Limiter at 1 A Range
Power Requirement
- 12 V - Power Supply for Automobiles
- 24 V - Power Supply for Automobiles
- Lithium-Ion Batteries
- Nickel-Hydride Batteries
Pulse Range
- 10 µs or Greater - Min. Pulse Width (External Input/Output)
- 100 µs to 3,600 seconds, 1 microsecond Resolution (During Source-Only Operation) - Pulse Width
Resolution
- 1 microsecond - Pulse Width, Period Time, Source & Measurement Delay
- 1 μV to 1 mV - DC Voltage Generation
- 100 PA to 10 μA - DC Current Generation
- 5.5-Digits - Output & Measurement Resolution
Response Time
- 100 µs: Time to Reach ± 0.1 % of Final Value at 20 V - Voltage Generation
- 400 µs: Time to Reach ± 1 % of Final Value at 20 mA - Current Generation
Supply Voltage
- 100-120 Vac
- 200 mV-110 V - Voltage Generation / Measurement Range
- 220-240 Vac
Update Time
- At Least 60 minutes - Warm-Up Time
